產品詳情
簡寫為:PVC電氣膠帶,PVC膠帶等等.具有良好的絕緣,耐燃,耐電壓,耐寒等特性,適用于電線纏繞,變壓器、馬達、電容器、穩壓器等各類電機、電子零件的絕緣固定用。有紅、黃、藍、白、綠、黑、透明等顏色。
適用于各種電阻零件的絕緣。如電線接頭纏繞,絕緣破損修復,變壓器、馬達、電容器、穩壓器等各類電機、電子零件的絕緣防護。也可用于工業過程中捆綁、固定、搭接、修補、密封、保護。
以聚氯乙烯薄膜為基材,涂以橡膠型壓敏膠制造。
電工膠帶專指電工使用的用于防止漏電,起絕緣作用的膠帶。具有良好的絕緣耐壓、阻燃、耐候等特性,適用于電線接駁、電氣絕緣防護等特點。
The devices covered under this category are incomplete in certain constructional features or restricted in perbance capabilities and are intended for use as components of complete equipment bted for investigation rather than for direct separate installation in the field. THE FINAL ACCEPTANCE OF THE COMPONENT IS DEPENDENT UPON ITS INSTALLATION AND USE IN COMPLETE EQUIPMENT SUBMITTED TO UL.
USE
This category covers painting equipment, air compressors, vacuum pumps and components intended to be used with or within Listed products of other categories.
REBUILT PRODUCTS
This category also covers painting equipment, air compressors and vacuum pumps that are rebuilt by the original manufacturer. Rebuilt painting equipment, air compressors and vacuum pumps are factory rebuilt to the extent necessary by disassembly and reassembly using new or reconditioned component parts. Rebuilt painting equipment, air compressors and vacuum pumps are subject to the same requirements as new painting equipment, air compressors and vacuum pumps.
UL's Rebuilt Products Program for this category does not allow for the rebuilding or refurbishing or pressure vessels.
CONDITIONS OF ACCEPTABILITY
Unless specified otherwise in the individual Recognitions, consideration is to be given to the following Conditions of Acceptability when these components are employed in the end-use equipment:
1. These components may have been investigated for systems under pressure. The hydrostatic test pressure rating is the maximum hydrostatic pressure at which these products were tested. The maximum system pressure/vacuum rating is denoted as "Pressure Rating," and is in terms of pounds per square in (psi) for compressors, and inches mercury (Hg) for vacuum pumps.
2. Special consideration should be given to polymeric materials when a product is investigated for a specific application. The Materials Rating should be suitable for the application as outlined in the end-product standard or specifications. The Materials Ratings are designated "MR":
MR=1 Unit employs "HB" minimum materials.
MR=2 Unit employs "V-2" minimum materials.
3. These products may have incomplete construction features which would need to be addressed in the end product. These Incomplete Construction Features, designated "ICF," include:
ICF=1 Guarding of hazardous moving parts may be required.
ICF=2 Suitable enclosure of live parts may be required.
ICF=3 Strain relief may be required.
ICF=4 A suitable pressure relief device may be required as the unit is capable of producing pressures above the load pressure rating of the unit.
ICF=5 Supply cord may be required.
4. These products have not been investigated for instruction manual requirements or for cautionary markings which may be required in the end-use application.
5. The suitability of the end-product connections to the motor terminals and the need for any strain relief and torque tests on the connection lead or power supply cord need to be determined in the end-product investigation.
6. The units have been investigated for use in normal use ambient (40°C maximum).
7. Products investigated to UL 60601-1, "Medical Electrical Equipment, Part 1: General Requirements for Safety," are based on non-patient contact for leakage current.
REQUIREMENTS
The basic standard used to investigate products in this category is UL 1450, "Motor-Operated Air Compressors, Vacuum Pumps, and Painting Equipment." These products may also be investigated to specific requirements outlined in the following standards designated "SC":
SC=1 UL 60601-1 (First Edition)
SC=2 UL 1950, "Safety of Inbation Technology Equipment" (Third Edition)
SC=3 UL 61010A-1, "Electrical Equipment for Laboratory Use; Part 1: General Requirements"
SC=4 UL 61010B-1, "Electrical Measuring and Test Equipment: - Part 1: General Requirements"
UL MARKING
Components Recognized under UL's Component Recognition Program are identified by markings consisting of the Recognized company's identification and catalog, model, or other product designation. In addition, components produced under the UL Component Recognition Program will also bear the Recognized Component Mark .
For rebuilt products the word "Rebuilt,""Refurbished" or "Remanufactured" precedes the catalog, model or other product designation.
The Listing or Classification Mark of UL is not authorized for use on, or in connection with, Recognized Components. Only those components that actually bear the "Marking" should be considered as being covered under the Component Recognition Program.
詳詢Sunny 陶 13913142465 QQ1822971259